Federal White Cement Federal White Cement Home Page

SUSTAINABILITY HOME
Federal White Cement Warehouse

PRODUCT DESCRIPTION
Masonry Cement: White Type N
Federal White Type N masonry cement can be used to match, contrast, and complement the colors of various masonry units, enhance the aesthetic color of a wall, or coordinate other colors in a design. It may be used for any masonry application where a white or a very light colored masonry joint is desired.

APPLICABLE STANDARDS
CSA A3002 Standard Specification for Masonry Cement
CSA A179 Mortar and Grout for Unit Masonry

Applications
Table 1 – A3002 Masonry Cement
Physical Requirements of Masonry Cements
Masonry Cement Type 28-Day Compressive Strength MPa (Min., psi) Water Retention Minimum % Air Content %
N (6.2) 900 70 8 - 21

Masonry Sand: Sand should meet the requirements of CSA A179 and be free of silt or clay fines and be from the same source. Buff or brown sands will impart an undertone of color to the mortar. This sand color may become more pronounced over time, or with cleaning, as sand particles are exposed on the surface of the mortar joint due to the erosion of the white mortar paste. To assure whitest mortar color, use only white sand.

USE
Federal White Masonry Cement is used to produce Types N mortar as defined within A179 “Mortar and Grout for Unit Masonry” and no admixtures are required or recommended.

Federal White Masonry Cement when mixed with the recommended volumes of sand meeting the requirements of CSA A179 will produce a mortar that will conform to the requirements of CSA A179 for the Proportion Specification found in Table 4 and the Property Specification found in Table 6.

Table 4 - A179 Proportion Specification
(Parts by Volume)
Mortar Type Masonry Type N Masonry Sand*
N 1 2 ¼ - 3
* measured in damp, loose condition

Under the Property Specification, the cement-to-sand proportions are to be in the range of 1:2 ¼ to 1:3 ½, and should meet the requirements in Table 6.
Download SDS SDS (Safety Data Sheet)

PDS PDF PDS (Product Data Sheet)


Table 6 - A179 Property Specification
Compressive Strength of Mortar Cubes
Preparation Mortar type 7-day test 28-day test
Job prepared or manufactured off site in a batching plant, mixed to a flow suitable for use in laying masonry units N 2 MPa (290 psi) 3.5 MPa (510 psi)
Laboratory prepared, mixed to a flow of 110 ± 5% N 3 MPa (435 psi) 5 MPa (725 psi)

INSTALLATION
White masonry mortar is applied using the same methods as any other CSA A179 mortar. Machine mixing should be used whenever possible. First, add most of the water and half of the sand. Next, add the masonry cement and the rest of the sand. After one minute of continuous mixing, slowly add the rest of the water. Mixing should continue for a minimum of five minutes which improves mortar color consistency and qualities.

No admixtures should be used without the written approval of the architect or engineer of record.

Water: All water should be clean and free from organic material and deleterious amounts of dissolved acids, alkalis and salts. The amount of water added should be the maximum that is consistent with adequate workability.

Retempering: To minimize retempering, mortar should not be mixed more than 15 minutes prior to use. Retempering will not adversely affect mortar quality if only evaporated water is replaced. Retemper white or colored mortar cautiously or not at all to avoid color changes.

Tooling of Joints: Tooling of mortar joints increases the density, durability and water tightness of the mortar surface. The moisture content of the mortar when tooled will affect the color; the drier the mortar, the darker its final color. Special care should be taken with white or very light-colored mortars to assure that joint surfaces are not discolored with metallic deposits from the jointer. It is recommended to use ceramic, stainless steel, or plastic jointers when working with such mortars.

Sample Panel: Final selection of mortar color should be determined on the basis of evaluation of a sample or mockup panel constructed using the units, mortar materials, mixing procedures, workmanship, tooling technique, and cleaning procedure that is proposed for use in the final project.

To assure consistent color on a project when using white or colored masonry mortar, the variables that determine mortar color such as materials, materials preparation, installation, and cleaning must be controlled.
MANUFACTURER
Federal White Cement
P.O. Box 1609
Woodstock, ON N4S 0A8

Sales Orders, Technical Service, Consultation, Product Information
Phone: 800-265-1806
Phone: 519-485-5410


WARRANTY
Federal White Cement warrants that the product identified is in accordance with the appropriate current CSA standard specification. No one is authorized to make any modifications or additions to this warranty. Federal White Cement makes no warranty or representation either expressed or implied with respect to this product and disclaims any implied warranty of merchantability or fitness for a particular purpose.

As Federal White Cement has no control over the other components mixed with this product or the final application, Federal White Cement does not and cannot warrant the finished work. The user is responsible for following industry standards and recommended practices. In no event shall Federal White Cement be liable for direct, indirect, special, or incidental or consequential damages arising out of the use of this product, even if advised of the possibility of such damages. In no case shall Federal White Cement liability exceed the purchase price of this product.

PRECAUTIONS
Freshly mixed cement, mortar, grout, or concrete may cause minor skin irritations. Avoid direct contact with skin and eyes and if contacted, wash exposed areas promptly with water. Refer to the applicable Federal White Cement product Safety Data Sheet (SDS) prior to use.

AVAILABILITY
Federal White Masonry Cement can be shipped to most destinations in Canada from our plant.

CONTACT US PROJECTS SUSTAINABILITY PRODUCTS ABOUT US Federal White Cement Federal White Cement Home Page